Test

Bulk Density Test
-Methods
-Manuals
-Procedures
-Calibration
-etc.

Labulk-0317 Aluminium Oxide Untamped Density Determination Principle

♦ Determination of the mass of a known volume of aluminium oxide collected after allowing it to fall freely into a stationary container, avoiding vibration. ♦ Expression of the untamped density by div ...
1. Labulk-0331 Fertilizer Bulk Density Tester Manual

1.1 Pour into the closed funnel a quantity of the fertilizer greater than that needed to fill the measuring cylinder. 1.2 Fully open the slide of the funnel so that the contents discharge into the mea ...
2. Labulk-0331 Fertilizer Bulk Density Tester Manual

2. If the fertilizer does not flow freely, keep the outlet clear by inserting a rod of 3 mm to 4 mm diameter into the opening. ...
3. Labulk-0331 Fertilizer Bulk Density Tester Manual

3. When the cylinder overflows, close the slide of the funnel and scrape away the surplus fertilizer using the spatula or other suitable tool. Avoid vibration of the filled measuring cylinder. ...
4. Labulk-0331 Fertilizer Bulk Density Tester Manual

4. Remove the measuring cylinder from below the funnel and weigh its contents to the nearest 1 g of the local mass. ...
5. Labulk-0331 Fertilizer Bulk Density Tester Manual

5. Carry out two determinations, in rapid succession, on separate test portions from the same test sample ...
1. Labulk-0308 Plastic Apparent Density Tester Manual – Procedure

1.1 With the apparatus assembled as in brochure, close the small end of the funnel with a flat strip and pour a 500±20-cm³ sample into the funnel. 1.2 Open the bottom of the funnel quickly and allow t ...
2. Labulk-0308 Plastic Apparent Density Tester Manual – Procedure

2.1 After all the material has passed through the funnel, immediately scrape off the excess on the top of the cup with a straightedge without shaking the cup. 2.2 Weigh the material in the cup to the ...
3. Labulk-0308 Plastic Apparent Density Tester Manual – Calculation

3.1 Apparent density = W/V where: V = volume occupied by the material in the measuring cylinder, cm³, W = weight of the material in the cylinder 3.2 Make three determinations of the apparent density o ...
1-Hall Flowmeter Preparation of Apparatus

1 Hall Flowmeter Preparation of Apparatus 1.1 Clean the funnel with clean dry toweling paper. 1.2 Clean the funnel orifice with a clean dry pipe cleaner. ...
3-Hall Flowmeter Test Procedure

3 Hall Flowmeter Test Procedure as-300-hall-flow-meter-test-2015-05-29 3.1 Weigh out a 50.0 g mass of powder, as sampled, into a clean weighing dish. AS-300A Automatic Hall Flowmeter by HMKTest 3.2 Bl ...
2. AS-100 Tap Density Tester Meet International Norms

AS-100 Tap Density Tester meets all international norms such as Applications in pharmaceutical (Compressibility Index/Carr’s Index and Hausner Ratio) – USP Chapter 616 Bulk Densit ...
2. AS-200 Scott Volumeter Principle

Put powder on the sieve set in the funnel complex, then the powder flow naturally or being driven into the chamber, passing four steel chips at angle of 25 degree and square funnel until being loaded ...
3. AS-100 Tap Density Tester Definitions

3.1 No.: Reference number of the test. 3.2 Weight: weight of the powder 3.3 Volume: volume of the powder 3.4 Tap Num: tap number of the test 3.5 Result: test result 3.6 TAP NUM: tap number 3.7 START: ...
3. AS-200 Scott Volumeter Structure

3.1 Top Funnel Complex: Made up of two cone-shaped stainless funnels, between them a stainless sieve (Dia.1.18mm) is set in 3.2 Chamber: the transect is square,4 glass sheet are set in the aluminum fr ...
4. AS-100 Tap Density Tester Specifications

4.1 Sample weight: ≤ 500 g 4.2 Sample volume: ≤ 250 ml 4.3 Single vibration number: ≤ 99999 (Error less than 1 of 10000. 4.4 Motor torque: 0.86 N.m. 4.5 Frequency: Max. 300 rpm / min (continuous adjus ...
4. AS-200 Scott Volumeter Sampling Procedure

4.1 For each sample to be tested, take at least 100cm3 and divide into 3 portions. 4.2 Usually, test the bulk powder as it is. For special ones user has to dry it. Dry powders subject to oxidize in va ...
5. AS-100 Tap Density Tester Features

5.1 Precision: Automatically keep five significant figures, accurate to four decimal places. 5.2 Auto Save: press “OK” the result is automatically saved including “Weight”, “TA ...
5. AS-200 Scott Volumeter Test Procedures

5.1 Take sample carefully on spoon and put them on the sieve in the Top Funnel Complex. The powder passes through the Chamber, Square Funnel and finally is loaded in the Cylinder Cup, stop loading if ...
6. AS-200 Scott Volumeter Calculation

The formula is as follows： as-200-scott-volumeter-calculation-formula In which: ρas: bulk density determined by AS-200 Scott Volumeter, g/cm³, M: mass of metallic powder, g; V: volume of bulk powder, ...